How to Install a Coaxial Cable Connector

How to Install a Coaxial Cable Connector At this info this is the How to Install a Coaxial Cable Connector, has been shared on this blog completely from start to finish. Hopefully this info will be useful to you and can be practiced.

Title : How to Install a Coaxial Cable Connector
Link : How to Install a Coaxial Cable Connector

Coaxial cable is a cable that has a copper conductor that is protected by an isulator, and the second conductor is a conductive sheet wrapped in dielectric (non-conductive) material. Here's how to connect your connector to a television coaxial cable.

Step

Initial Step :

Determine the size of the cable. Cable terminology can be confusing. Look at the side of the coaxial cable to find the size. In most homes, the two most common cable sizes are RG-6 and RG-59.
- RG stands for "Radio Guide"The numbers on various cable versions refer to diameter (59 means 0.059, and 6 means 0.06, etc.) and the internal characteristics of the cable, including the number of shields and attenuation of the cable, which refers to how much the signal is lost per cable length.
- You can also see RF letters printed on this cable, which stands for "Radio Frequency"
- Most nonindustrial coaxial cables are now known as RG-6, although thinner, lower quality RG-59 cables are still used in some devices and older homes. Commercial technicians use thicker GE cables, such as RG-11 (which are only used if the distance from the source to the termination point is more than 60 meters)
- RG cable used at home for everyday use has a size of 75 ohms (RG-6 or RG-59).
- Know that all cables (and their connectors) are available in a variety of qualities. Choose the best quality available.
Choose the right connector. Most connectors for home video installation are made with type F connectors. However, there is a possibility that your device still uses N type connectors.
- Know that there are several type F cables available, typically screw type connectors and crimp.
  - Screw connectors are easy to use, but less secure and leave small airbags, which can affect signal quality.
  - Type connector crimp has two parts: ring (or crimp) and terminator. This connector is usually difficult to install, but produces the best length and quality if used correctly.
- Know that you need the same type of male and female connectors to make a connection.
  - The male connector has a wire sticking out in the middle, while the female connector has a hole for the middle wire to enter. Make sure you use connectors with the opposite genre. Most cables have a male plug end.
- Use the SMA connector (sub-miniature Version A) for very small coaxial cables.

Unlock the cable

The first Step : in installing the connector is to prepare the end of the coaxial cable.

Cut the end of the cable.
Open the outer layer (usually black rubber) as far as 1.5 cm.
- Be careful not to cut the metal layer directly behind the outer insulation skin. This layer can be "loose" wire and sheet metal behind the cable protector.
Peel the inner metal sheet (second channel) carefully and open the outer insulation layer. Make sure the metal does not wrap around or touch the copper core conductor.
Cut the dielectric plastic (usually white or clear) from the inner core cable.
- You must make sure not to scratch or pry the central conductor. All damage to this conductor will worsen the signal quite badly.
Push the connector down past the end of the cable to raise the copper core of the coaxial cable.
- Make sure the dielectric (aluminum paper) has been cut so that it does not enter the terminator on the conductor.
Attach the connector to the end of the cable. The connector flow will cut to casing outside and wrap protective fabric so that it is securely fastened.

Using the Type Connector Crimp

This is another method for connecting a coaxial cable connector.

Attach the ring crimp at the end of the cable.
Open the outermost layer of the cable to about 1 cm.
Cut the protective layer, the metal layer, and the dielectric so that the remaining wire core wires.
Leave the dielectric 0.5 cm long.
Install the terminator on the end of the cable so that the copper core sticks out of the hole.
Push the connector crimp down to the end of the cable so that the connector tube is between the aluminum layer and casing outside of
- This Step : is quite difficult. Try to hold the end of the cable with tan, and not twist the connector when pushing it.
Use crimper on the ring around the outside of the cable.
Cut the remaining dangling wire.
Cut the end of the inner core wire so that it is evenly distributed to the end of the connector.
Close the connector to make sure it is installed properly.

Tips

If you have high-speed internet and more than one television, make sure you use the RG type 6 connector. Preparation is needed before connecting the connector with the cable wire to get clear images and solid connections for modern cables. Use the compression type connector that is usually sold at home supply stores. Also, make sure not to "scratch" or pry the copper conductor core because it will cause problems on the internet, such as intermittent connectivity and packet loss.
You can buy a tool crimper, cutter and stripper which is specifically designed for coaxial cables in certain diameters. You need training to be able to use this tool, and actually the tool is not needed to make a connection. Tool stripper it's enough as long as you are careful.
Do not use type F screw connectors. Cable signals will "leak" to these cheap and low-quality connectors. This connector can cause unwanted signals to "enter" into the cable and cause strange distortions in the form of vertical lines, dotted lines that move horizontally along the screen and "beats"or small white dots randomly across the screen.

Warning

Professionals use coaxial compression fittings with compression tools that are no more expensive than crimper. This tool is more often used now because it produces a seal that is more waterproof and has a minimal impact on sunyal at the joint point.
Make sure you use a good connector. Don't work halfway. Cable TV signals can leak bad connectors and interfere with many devices using RF technology (including aircraft). What's more, if too many signals leak, you can be punished.
If you are unsure, leave it to your professional cable television service provider. Usually the rates charged are quite cheap, especially when compared to electrical contractors.

Things You Need

Cable cutter
Stripper/ RG-6 cable opener
Channel locking pliers
RG6 connector
Tool crimper
Stripper cable

Source

http://www.bluejeanscable.com/articles/rg6.htm – All about GM
http://en.wikipedia.org/wiki/Coaxial_cable – Coaxial subject matter.

Source link & Translate By :

Similarly, info How to Install a Coaxial Cable Connector, hopefully this info can be useful for you all, and good luck.